STM32F2系列外設設置規則
掃描二維碼
隨時隨地手機看文章
外設設置規則：
在配置之前必須添加外設的.c文件，以及相應包含的.h。.h文件在stm32f2xx_conf.h中添加。
1、 時鐘設置：包括引腳時鐘和外設時鐘：
RCC_XXXPeriphClockCmd();
2、 引腳連接：即把引腳和外設功能進行連接；
GPIO_PinAFConfig();
如下功能需要引腳與外設連接。
* @arg GPIO_AF_RTC_50Hz
* @arg GPIO_AF_MCO
* @arg GPIO_AF_TAMPER
* @arg GPIO_AF_SWJ
* @arg GPIO_AF_TRACE
* @arg GPIO_AF_TIM1
* @arg GPIO_AF_TIM2
* @arg GPIO_AF_TIM3
* @arg GPIO_AF_TIM4
* @arg GPIO_AF_TIM5
* @arg GPIO_AF_TIM8
* @arg GPIO_AF_TIM9
* @arg GPIO_AF_TIM10
* @arg GPIO_AF_TIM11
* @arg GPIO_AF_I2C1
* @arg GPIO_AF_I2C2
* @arg GPIO_AF_I2C3
* @arg GPIO_AF_SPI1
* @arg GPIO_AF_SPI2
* @arg GPIO_AF_SPI3
* @arg GPIO_AF_USART1
* @arg GPIO_AF_USART2
* @arg GPIO_AF_USART3
* @arg GPIO_AF_UART4
* @arg GPIO_AF_UART5
* @arg GPIO_AF_USART6
* @arg GPIO_AF_CAN1
* @arg GPIO_AF_CAN2
* @arg GPIO_AF_TIM12
* @arg GPIO_AF_TIM13
* @arg GPIO_AF_TIM14
* @arg GPIO_AF_OTG1_FS
* @arg GPIO_AF_OTG2_HS
* @arg GPIO_AF_ETH
* @arg GPIO_AF_FSMC
* @arg GPIO_AF_OTG2_FS
* @arg GPIO_AF_SDIO
* @arg GPIO_AF_DCMI
* @arg GPIO_AF_EVENTOUT
3、 初始化GPIO配置：
GPIO_Init();
4、 外設初始化：
如UART初始化如下：
USART_InitStructure.USART_BaudRate = 115200;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USARTx, &USART_InitStructure)；
ADC初始化如下：（多路模式）
// DMA1_Stream0 channel0 configuration **************************************/
DMA_DeInit(DMA2_Stream0);
DMA_InitStructure.DMA_Channel = DMA_Channel_0;
DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)ADC1_DR_ADDRESS; //定義外設基址
DMA_InitStructure.DMA_Memory0BaseAddr = (uint32_t)&ADCConvertedValue; //定義寄存器基址
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralToMemory; //定義DMA傳輸模式從外設到內存
DMA_InitStructure.DMA_BufferSize = 4; //定義buffer大小，根據通道數來定
DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable; //外設地址寄存器不變
DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable; //DMA寄存器隨之增加（單通道不增加）
DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_HalfWord; //DMA外設數據大小，16位半字
DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_HalfWord; //DMA存儲器數據大小，16位半字
DMA_InitStructure.DMA_Mode = DMA_Mode_Circular; //模式為循環模式
DMA_InitStructure.DMA_Priority = DMA_Priority_High; //DMA優先級高
DMA_InitStructure.DMA_DirectMode = DMA_DirectMode_Disable; //直接傳輸模式無效 DMA_InitStructure.DMA_FifoThreshold = DMA_FifoThreshold_HalfFull;
DMA_InitStructure.DMA_MemoryBurst = DMA_MemoryBurst_Single;
DMA_InitStructure.DMA_PeripheralBurst = DMA_PeripheralBurst_Single;
DMA_Init(DMA2_Stream0, &DMA_InitStructure);
//************ DMA2_Stream0 enable ************/
DMA_Cmd(DMA2_Stream0, ENABLE); //使能DMA流0
//***************** ADCs DeInit ***************/
ADC_DeInit(); //ADC重初始化
//************* ADC Common Init ****************/
ADC_CommonInitStructure.ADC_Mode = ADC_Mode_Independent; //ADC獨立模式
ADC_CommonInitStructure.ADC_Prescaler = ADC_Prescaler_Div2; //ADC采樣周期2分頻
ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled;
ADC_CommonInitStructure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles; //采樣周期
ADC_CommonInit(&ADC_CommonInitStructure); //基本初始化
//*************** ADC1 Init ********************/
ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b; //ADC采樣精度
ADC_InitStructure.ADC_ScanConvMode = ENABLE; //采用掃描模式，因?yàn)槎嗦?/p>
ADC_InitStructure.ADC_ContinuousConvMode = ENABLE; //連續掃描模式
ADC_InitStructure.ADC_ExternalTrigConvPolarity = ADC_ExternalTrigConvPolarity_None;//無外部觸發
ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right; //數據右對齊
ADC_InitStructure.ADC_NbrOfChannel = 4; //采樣通道數
ADC_Init(ADC1, &ADC_InitStructure);
//************ ADC1 regular channel12 configuration ************/
ADC_RegularChannelConfig(ADC1, ADC_Channel_4, 1, ADC_SampleTime_3Cycles);
ADC_RegularChannelConfig(ADC1, ADC_Channel_5, 2, ADC_SampleTime_3Cycles);
ADC_RegularChannelConfig(ADC1, ADC_Channel_6, 3, ADC_SampleTime_3Cycles);
ADC_RegularChannelConfig(ADC1, ADC_Channel_7, 4, ADC_SampleTime_3Cycles);
//********* Enable DMA request after last transfer (Multi-ADC mode) *********/
ADC_DMARequestAfterLastTransferCmd(ADC1, ENABLE);
//*********** Enable ADC1 DMA ****************/
ADC_DMACmd(ADC1, ENABLE);
//*************** Enable ADC1 ***************/
ADC_Cmd(ADC1, ENABLE);
//******* Start ADC1 Software Conversion *****/
ADC_SoftwareStartConv(ADC1); //軟啟動開始采樣
5、 中端配置：
以下為串口中斷配置：
void NVIC_Configuration(void)
{
NVIC_InitTypeDef NVIC_InitStructure;
/* Configure the NVIC Preemption Priority Bits */
/* Configure one bit for preemption priority */
/*優先級組說明了搶占優先級所用的位數，和子優先級所用的位數在這里是1，7 */
NVIC_PriorityGroupConfig(NVIC_PriorityGro
下載文檔
