多臺電機獨立控制 控制要求: 為兩臺異步電動機設計一個控制線路,其要求如下: (1)兩臺電動機互不影響地獨立工作; (2)能同時控制兩臺電動機的起動與停止; (3)當一臺電動機發生故障時,兩臺電動
直流電動機控制電路-DC Motor Control CircuitNotes: Here, S1 and S2 are normally open , push to close, press button switches. The diodes can be red or green and are there only to indicate direction
音量指示器--Sound Level IndicatorThis project uses an LM3915 bar-graph IC driving two sets of ten LEDs for a 30dB range. The circuit is unique because it has an additional range of 20dB provided by an
簡單伺服測試儀電路--Simple Servo Testerclick here to download schematic in pdfThis is a simple servo tester which will comprehensively test the capabilities of almost any modern servo. It has two push
風扇控制器電路-Fan controlThis is a simple circuit that will do what you want I believe. R1 15k ohm resistor NTC Thermistor- 10k ohm, sold at Radio Shack in the states. P1 10k ohm potentiometer -
可調頻閃燈電路--Adjustable Strobe LightThis one uses a much more powerful "horse shoe" Xenon tube which produces more light. You can also control the flash rate up to about 20Hz. Do not look
單極性步進電機控制器電路--Unipolar Stepper Motor ControllerThis is a very good integrated circuit. There is no need for any external glue logic to drive the circuit, there is only 2 pins to drive the
PWM馬達/燈控制器電路-PWM Motor/Light ControllerA pulse width modulator (PWM) is a device that may be used as an efficient light dimmer or DC motor speed controller. The circuit described here is a gen
黑光發生器電路 Black Light This circuit is a simple ultraviolate light that can be powered by a 6 volt battery or power supply that is capable of supplying 1 or more amps. Theoritical DiagrammPARTSP
擊落模型定位器電路 (Downed Model Locator II)Here is another device to help you locate your downed R/C sailplane in the bushes and weeds. Similar to the other design, this circuit plugs into a spare s
紅外遙控電路--Infrared Remote ControlThis circuit will allow you to turn on any piece of equipment that operates on 115 volts ac. The reciever circuit is based on the Radio Shack infrared receiver mod
紅外線開關電路-Infra Red SwitchThis is a single channel (on / off) universal switch that may be used with any Infra Red remote control that uses wavelengths between 850-950nm.Notes: Any "button&
接收機電池低電壓報警電路--Receiver Battery Low Voltage AlarmHere is another equally cool low voltage alarm circuit for your glider receiver battery that I've shamelessly stolen from George Steiner's b
電池組接收機的放電電路--Discharger for Receiver Battery PacksYou may have read about cycling NiCad batteries. If not, read a little here ( Red's R/C Battery Clinic) for an excellent overview. Overch
Description This launch controller can be used with low voltage battery igniters, which fire rocket engines in model rockets such as the Estes range. These circuits are electrical, only switches and