TI公司的TIDA-01476是低功耗無線PIR運動檢測參考設計,能創建工業傳感器到云端節點,連接到IoT網絡網關和云數據提供者.參考設計采用微功耗運放,比較器和SimpleLink™超低功耗小于1GHz無線微控制器(MCU)平臺等器件,以形成超低功耗傳感器-云運動檢測器,具有超長電池壽命和不需要連線.連接長度高達1000米,滿足IEEE 802.15.4e/g標準,主要用在運動檢測,照明傳感器,無線控制和建筑物自動化.本文介紹了參考設計TIDA-01476主要特性和系統指標,框圖,電路圖,材料清單和PCB設計圖.

The TIDA-01476 reference design demonstrates howto create an industrial sensor-to-cloud end nodecapable of connecting to an IoT network gateway andcloud data provider. This design uses TexasInstruments’ nano-power operational amplifiers,comparators, and the SimpleLink™ ultra-low-powerSub-1 GHz wireless microcontroller (MCU) platform todemonstrate an ultra-low-power sensor-to-cloudmotion detector, leading to extremely long battery lifeand no required wiring.

This reference design demonstrates how to create an industrial sensor-to-cloud end node capable of connecting to an IoT network gateway and cloud data provider. This design uses Texas Instruments’ nano-power operational amplifiers, comparators, and the SimpleLink™ ultra-low-power Sub-1 GHz wireless microcontroller (MCU) platform to demonstrate an ultra-low-power sensor-to-cloud motion detector, leading to extremely long battery life and no required wiring.

Many industrial and building automation systems use motion detectors to control different functions basedon human presence, such as lighting, for achieving higher efficiency of those functions by turning them offwhen not needed. Additionally, these systems require increasing numbers of wireless sensor nodes toreduce the installation costs and the make the systems more flexible for future expansion by eliminatingwiring. However, one of the major limitations for a large wireless network is power. Because thesesystems are battery powered, the maintenance cost associated with periodic battery replacement can　become prohibitive. Depending on the power consumption and battery configuration, typical batterypoweredPIR motion detectors can run anywhere from four to seven years before the batteries need to bereplaced.

Enabled by Texas Instruments ’nano-power amplifiers, comparators, and the SimpleLink ultra-low-powerwireless MCU platform, the Low-Power Wireless PIR Motion Detector Reference Design demonstrates amotion detector circuit solution requiring no wiring while also fully maximizing the battery life.

At a high level, this TI Design consists of a CR2032 coin cell battery, two nano-power op amps, two nanopowercomparators, an ultra-low-power wireless MCU, and a PIR sensor with analog signal output. Thetwo op amps form an amplified band-pass filter with a high-input impedance, which allows it to beconnected directly to the sensor without loading it. The two comparators form a window comparator, whichis used to compare the amplified sensor output to fixed reference thresholds so that motion can bedistinguished from noise. The two outputs of the window comparator then serve as interrupts to the　wireless MCU. This way, the MCU can operate in its lowest power sleep mode during times where there isno motion being detected and only wakes up to send messages back to a remote host when motion hasbeen detected. Due to the nano-amp operation of the analog signal chain components, this TI Designachieves a 10-year battery life from a single CR2032 coin cell battery.

This design guide addresses component selection, design theory, software and the testing results of thisTI Design system. The scope of this design guide gives system designers a head-start in integrating TI’snano-power analog components, and the SimpleLink ultra-low-power wireless MCU platform along with astarting point for sensor-to-cloud software integration.

參考設計TIDA-01476主要特性:

• Large Network-to-Cloud Connectivity EnablingLong Range, Up to 1 km (Line of Sight)
• IEEE 802.15.4e/g Standards-Based Sub-1 GHzSolution With TI 15.4-Stack
• Use of Nano-Power Analog for Ultra-Low-PowerDesign, Resulting in 10-Year Battery Life FromSingle CR2032 Coin Cell
• Low Standby Current of 1.65 μA (PIR SensorRemains Active in Standby)
• Interrupt Driven Sub-1 GHz WirelessCommunication of Motion for Increased Power Savings
• Motion Sensitivity up to 30 ft

參考設計TIDA-01476應用:

• Motion Detection
• Lighting Sensors
• Wireless Controls
• Building Automation

圖1.參考設計TIDA-01476外形圖
參考設計TIDA-01476主要系統指標:

圖2.無線PIR系統框圖

圖3.低功耗無線PIR運動檢測器參考設備硬件描述

圖4.參考設計TIDA-01476電路圖(1)

圖5.參考設計TIDA-01476電路圖(2)

圖6.參考設計TIDA-01476電路圖(3)
參考設計TIDA-01476材料清單:

圖7.參考設計TIDA-01476 PCB圖

圖8.參考設計TIDA-01476 PCB設計圖(1)

圖9.參考設計TIDA-01476 PCB設計圖(2)

圖10.參考設計TIDA-01476 PCB設計圖(3)

圖11.參考設計TIDA-01476 PCB設計圖(4)

圖12.參考設計TIDA-01476 PCB設計圖(5)

圖13.參考設計TIDA-01476 PCB設計圖(6)

圖14.參考設計TIDA-01476 PCB設計圖(7)

圖15.參考設計TIDA-01476 PCB設計圖(8)
詳情請見:

和
以及
與
tiduda8.pdf
tidrs11.pdf
tidrs12.pdf