#ifndef __SYS_H_

#define __SYS_H_

#include "common.h"

#define SystemCoreClock 120000000 //cpu時鐘頻率,計算時有用

#define ApbClock 120000000 //120M

#define EmcClock 60000000 //60M

#define UsbClock 48000000 //48M

void SystemInit(void);//系統時鐘初始化,啟動代碼調用

#endif

#include "sys.h"

#define XTAL_FREQ 12000000

#define LPC_PBOOST *((volatile unsigned long *)(0X400FC1B0))

void SystemInit(void)

{

LPC_SC->SCS=0x00000021;//osc晶振使能,地址線不移位模式

while((LPC_SC->SCS&(1<<6))==0);/* 等待osc晶振準備好 */

LPC_SC->CLKSRCSEL=0x00000001; /*選擇osc為系統輸入時鐘*/

LPC_PBOOST|=(3<<0); //打開功耗提升,可以提升到120MHZ

// PLL0 Configuration (Main PLL)

// PLL0 Configuration Register (PLL0CFG)

// PLL out clock = (F_cco / (2 * P))

// F_cco = (F_in * M * 2 * P)

// F_in must be in the range of 1 MHz to 25 MHz

// PLL out clock must be in the range of 9.75 MHz to 160 MHz

// F_cco 156-320M

// MSEL: PLL Multiplier Selection 0-4bit m

// M Value

// PSEL: PLL Divider Selection 5-6bit p

// P Value

// 1

// 2

// 4

// 8

LPC_SC->PLL0CFG=0x00000009;//選擇倍頻系數 P = 1 M = 10 FCCO = FIN*P*M*2=240M PLL_OUT = FCCO/(2*P)=120M

LPC_SC->PLL0CON=0x01; /* PLL0 使能 */

LPC_SC->PLL0FEED=0xAA;

LPC_SC->PLL0FEED=0x55;

while(!(LPC_SC->PLL0STAT&(1<<10)));/* 等待PLL鎖定 */

LPC_SC->PLL1CFG=0x00000023;//選擇倍頻系數 m = 4 p = 2 fcco = fin*2*p*m = 192m pllout = 192/2*p = 48M

LPC_SC->PLL1CON=0x01; /* PLL1 使能 */

LPC_SC->PLL1FEED=0xAA;

LPC_SC->PLL1FEED=0x55;

while(!(LPC_SC->PLL1STAT&(1<<10))); /* 等待PLL1 鎖定 */

LPC_SC->CCLKSEL=(1<<0)|(1<<8); /* pll0為主時鐘,分頻數為1 */

LPC_SC->USBCLKSEL=(1<<0)|(2<<8); /* pll1為cpu主時鐘 */

LPC_SC->EMCCLKSEL=(1<<0); /* EMC 為系統是時鐘的一半 */

LPC_SC->PCLKSEL=(1<<0); /* 外設時鐘分頻數為1,120M */

LPC_SC->PCONP=0x00; /* 可以關閉的外設全部被關閉 */

LPC_SC->CLKOUTCFG&=~(1<<8); /* 停止時鐘輸出 */

LPC_SC->FLASHCFG=(5<<12)|0x03A;//6個cpu flash訪問時鐘,最安全的設置,120M時候可用

#ifdef __RAM_MODE__//設置中斷向量表的位置,一般不改

SCB->VTOR=0x10000000&0x3FFFFF80;

#else

SCB->VTOR=0x00000000&0x3FFFFF80;

#endif

}